ADC-700X Outdoor Camera Guide

Common Terms

Transformer (Power Brick)

The low-voltage power supply that plugs into your wiring to power devices.

Wi-Fi Extender (Range Booster)

A device that amplifies and extends your wireless network’s coverage.

AP Mode (Access Point Mode)

A router setting that lets your device act as a Wi-Fi hotspot for other devices.

WPS (Wi-Fi Protected Setup)

A quick way to connect devices to your Wi-Fi network without entering a password.

VMD (Video Motion Detection)

A camera feature that triggers recording or alerts when motion is detected.

Perimeter Guard (Perimeter Detection)

An Alarm.com rule that monitors predefined zones for motion or entry.

PoE (Power over Ethernet)

Supplies both power and network data over a single Ethernet cable.

IR (Infrared)

Infrared LEDs that enable night vision in zero-light conditions.

IP66 (Ingress Protection Rating)

Weatherproof rating: dust-tight and protected against powerful water jets.

FOV (Field of View)

The camera’s horizontal and vertical viewing angles.

Specifications

• Video resolution: 640 × 480 pixels (VGA)
• Night-vision range: up to 40 ft (0 lux IR)
• Field of view: 56° H × 42° V
• Connectivity: Ethernet only (no Wi-Fi)
• Power: PoE (802.3af) or included AC adapter
• Operating temperature: –4 °F to 122 °F; up to 90% humidity

Features

• Weatherproof housing (IP66)
• Day/night IR with auto IR-cut filter
• Adjustable video motion detection zones
• Offsite cloud storage—no local DVR needed
• Remote live view & playback via your Brinks Home account
• Event-triggered recording with compatible panels

Factory Default

1. Remove the wiring cover and rubber insert, then unscrew and remove the rear housing.
2. Press and hold the reset button for 90 s until the LED flashes rapidly red.
3. Reassemble the housing and wait for the camera to reboot.

Disclaimer: After factory reset, please contact us to update your Brinks Home account with the camera’s new settings. You can text 469-513-8685 or call 469-391-4024.

Wiring & PoE Setup

1. Connect an Ethernet cable from the camera’s RJ45 port to your router or network switch.
   
2. For PoE, plug the camera cable into the PoE injector’s LAN port, then connect the injector to your switch:
   
3. Alternatively, use the included AC adapter if PoE isn’t available.

Add via Desktop App

Note: Ensure the camera is powered and network-connected.

1. Open a web browser and go to alarm.com.
2. Log in with your Brinks Home credentials.
3. Click Video in the top navigation.
   
4. Click Settings.
5. Scroll down and click Add Video Device.
   
6. Select ADC-V700X, enter a name, then click Install.
   
7. Wait for setup to finish, then click Live View to confirm.
   

Add via Brinks Home App

Note: Camera must be online first.

1. Open the Brinks Home App on your smartphone.
2. Tap the bottom-bar icon labeled Video.
   
3. Tap the ⚙️ gear icon in the top-right corner.
   
4. Select ADC-V700X, enter a name, then tap Next.
   
5. Wait for configuration to finish, then tap Live View.
   

Optional Accessories

• ADC-VPE: 9′ DC power extension cable
• ADC-POE-INJ: PoE injector
• Waterproof RJ45 connector kit

Troubleshooting

1. Is the camera offline in your Brinks Home app?
   1. Yes:
      1. Check that the Ethernet cable is securely plugged in.
      2. Verify PoE injector or AC adapter is powered.
      3. Reboot your router or switch.
   2. No: Continue below.
2. Is there no live view image?
   1. Confirm the camera lens is unobstructed.
   2. Ensure the camera has fully rebooted after power-cycle.
   3. Check your Brinks Home app settings for any disabled video streams.
3. Are recordings not appearing?
   1. Make sure your panel or plan supports event-triggered recording.
   2. Verify VMD zones are properly configured in your Alarm.com rules.

LED Reference Guide

Further Assistance

If you need additional help, please contact us at 469-513-8685. We’re here to help!