ADC-V521IR Indoor Camera Guide

Common Terms

Transformer (Power Brick)

The low-voltage power supply that plugs into your wiring to power the camera.

Wi-Fi Extender (Range Booster)

Expands your wireless signal’s reach to improve connectivity.

AP Mode (Access Point Mode)

Allows you to connect directly to the camera’s Wi-Fi network for manual setup.

WPS (Wi-Fi Protected Setup)

A quick setup method using the WPS button on your router and camera—no password required.

VMD (Video Motion Detection)

Triggers recording or alerts when the camera senses motion.

Perimeter Guard (Perimeter Detection)

A smart rule that monitors defined areas for movement or intrusion.

Specifications

• 1920 × 1080p HD resolution
• 112° horizontal × 100° vertical field of view
• Up to 20 ft infrared night vision
• Two-way audio
• Wi-Fi (802.11 b/g/n) and Ethernet (10/100 Mbps)
• Operating temperature: 32 °F to 104 °F

Factory Default

Warning: Resetting your camera erases all settings. You must contact us after a reset to reconnect it to your account. Call 469-513-8685.

1. Press and hold the button on the back of the camera for 15 seconds.
2. Release when the front LED flashes red and green.

Wi-Fi Setup (WPS Mode)

1. Plug in the camera and wait about 2 minutes until the LED is solid red.
2. Hold the back button for 5 seconds until the LED flashes blue.
3. Within 30 seconds, press your router’s WPS button.
4. Wait up to 2 minutes. A solid green LED means success; a red LED means try again or use AP Mode.

Camera LED turns red when ready

Wi-Fi Setup (Access Point Mode)

1. Hold the back button for 6 seconds until the LED flashes white.
2. On your device, join the Wi-Fi network named Alarm xx:xx:xx.
3. Open a browser to 192.168.1.1.
4. Tap Scan, select your network, enter your password, then tap Submit.
5. Wait for the LED to turn solid green.

Signal Strength Guidance

1. Open the Brinks Home™ App.
2. Tap the Video icon.
3. Tap ⚙️ in the top-right corner.
4. Select your camera.
5. Scroll to Signal Strength percentage.

Hardwired Ethernet Setup

1. Connect the LAN port on the camera to your router using an Ethernet cable.
2. Power on the camera and wait for the LED to turn solid green.

Add via Desktop App

1. Go to Brinks Home™ login and sign in.
2. Click Video, then the Settings gear icon.
3. Click Add Video Device and select ADC-V521IR.
4. Name your camera and click Install.
5. After installation, click Live View to verify your feed.

Add via Brinks Home™ App

1. Open the Brinks Home™ App and tap the Video icon.
2. Tap the Settings gear icon, then tap Add Video Device.
3. Select ADC-V521IR and name the camera.
4. Tap Next and wait for setup to complete.
5. Tap Live View to confirm the video feed.

Mobile App: Video Section

Optional Accessories

• PoE Adapter Kit (power and data over one cable)
• Wall Mounting Bracket (flexible installation angles)
• Ethernet Extension Cable (for longer runs)
• USB Power Adapter (spare power brick)

Troubleshooting

• Camera not powering on:
  1. Ensure the power adapter is securely plugged in.
  2. Test the outlet with another device.
  3. Try a different power adapter if needed.
• Solid Red LED (No network):
  1. If wired, reseat the Ethernet cable and use another router port.
  2. If wireless, repeat WPS or AP Mode setup.
• Flashing Green LED (Local network only):
  1. Reboot your internet router.
  2. Power cycle the camera (unplug 10 seconds, then plug back in).
• Poor image quality:
  1. Clean the lens with a soft, lint-free cloth.
  2. Avoid pointing at bright lights or reflective surfaces.
  3. In the Brinks Home™ App, adjust resolution or brightness.
  4. For Wi-Fi issues, check the Signal Strength section above.

LED Reference Guide

Further Assistance

If you need additional help, please contact us at 469-513-8685.